Skip to content

Basler Opto-GP-I/O Y-Cable, HRS 6p/open, P, 2 x 10 m#

Input/Output (I / O) cable with a Hirose 6-pin connector at one end (camera side) and two open-ended cables at the other end (host side).

Basler Opto-GP-I/O Y-Cable, HRS 6p/open, P, 2 x 10 m

Info

The cable is suitable for the following camera models:

  • ace USB 3.0
  • ace GigE
Order Number Cable Length
2000034088 2 x 10 m

Depending on the camera model, the wires in the cable with the yellow outer jacket connect to different pins of the camera:

Camera Model Wires Connect to
ace USB 3.0
ace GigE (with GPIO)
Direct-coupled general purpose I/O (GPIO) pins (GPIO, GPIO Ground) of the camera
ace GigE (without GPIO) Power supply of the camera

Cable Drawing#

Cable Drawing

CAUTION – Personal Injury Hazard

Personal injury hazard and risk of damage to camera in case of short circuits (applies to GigE cameras only)

Short circuits may cause an extreme rise in temperature of the camera's housing. This may damage the camera and may also lead to personal injuries, e.g., burns if touching the housing. In the worst case, the overheating may cause a fire. In order to prevent that, you should take additional measures to limit the current flowing through each individual wire during a short circuit. The maximum current allowed is 2 A. There are two ways how to do this:

  • Using a fuse
  • Using a limited power supply

Wiring Information#

Pin Number Wire Color (Opto-I/O End)
(Blue Cable)
Function (USB 3.0 Cameras & GigE Cameras)
1 n/a n/a
2 Brown Opto-isolated IN (Line 1)
3 n/a n/a
4 Yellow Opto-isolated OUT (Line 2)
5 White/Green Opto-isolated Ground
6 n/a n/a
Pin Number Wire Color (GP-I/O End)
(Yellow Cable)
Function
USB 3.0 Cameras
Function
GigE Cameras
1 Brown GPIO (Line 3) Camera Power
2 n/a n/a n/a
3 Yellow GPIO (Line 4) GPIO (Line 3)
(only models with GPIO)
4 n/a n/a n/a
5 n/a n/a n/a
6 White/Green GPIO Ground Camera Power Ground
GPIO Ground (only models with GPIO)

Info

To achieve the best possible signal-to-noise ratio, both ground wires have to be connected to ground. Additionally, if you're not using one of the GPIO lines, connect the ground wire to ground as well.

Physical Specifications#

Camera-side Connector Hirose 6 pin [HR10A-7P-6S (73)]
Host-side Connector None, open end
Cable Cross-sections Host-side cables, each: 2 × 2 × 0.14 mm² (close to AWG 26)
Cable Diameter (Camera/Host Side) Camera side: 5.8 mm max.
Host side: 4.9 mm max.
Wire Insulation PVC
Outer Jacket PVC
Minimum Bending Radius (Camera Side) 29.4 mm (6 x cable diameter), fixed installation
Minimum Bending Radius (Host Side) 34.3 mm (7 x cable diameter), fixed installation
Maximum Bending Cycles (Camera/Host Side) None (fixed installation only)
Suitable for Drag Chain Applications No
Suitable for Robotics Applications No

Electrical Specifications#

Maximum Operating Voltage See camera documentation for the power requirements of your camera.
Wire Resistance ≤142 Ω/km

Environmental Specifications#

Operating Temperature Range -25–80 °C, not moving

Plug Specifications#

Durability >1000 mating cycles
Contact Resistance 10 mΩ max.
Contact Plating Silver
Protection Rating IP40
Plug Insulation Material Polyamide/PBT

General Information#

Conformity CE (includes RoHS)
Certificates for your cable
For more information, see the Compliance section of the Basler website.
Warranty 3 years

Read the topic about your camera model before connecting the cable to the camera. You can find your camera topic in the Area and Line Scan Cameras section under "Models".