Skip to content

Hardware Installation (GigE Cameras)#

This topic tells you how to install a Basler camera with a GigE interface.

General Considerations#

The pylon Camera Software Suite for Windows must be installed.

Make sure that the following items are available before starting the hardware installation:

  • A Basler camera with a GigE interface.
  • A computer with a suitable GigE network adapter.
  • As applicable, a power supply or a PoE power injector.
    Make sure that the power supply meets all of the requirements listed in the topic about your camera model.
    If you want to use PoE, your camera supports PoE, but your computer doesn't, use a PoE injector. Alternatively, you can make your computer PoE-capable by using a network card with added PoE capabilities, for example this one.
  • As applicable, a C-mount or CS-mount lens for the camera.
    If you already know what lens you will be using in your actual application, use this lens during the camera installation and setup. If not, Basler suggests using a zoom lens for the installation and initial setup. Contact Basler technical support if you need assistance in determining the best lens for your application.
  • A standard Ethernet cable. Basler recommends using Cat 6 or Cat 7 S/STP cables. If you're using a PoE injector, you need two Ethernet cables.
    Suitable cables are available via the Basler website.

Basler 1GigE Cameras#

The following GigE network adapters are recommended for use with Basler 1GigE cameras:

  • Intel Pro 1000 series
  • Intel i210 series
  • Intel i340 series
  • Intel i350 series

These adapters have been tested and generally work well with the pylon GigE Vision drivers.

However, for best performance, Basler recommends using the Basler GigE Interface Cards.

Basler 5GigE Cameras#

The following GigE network adapter is recommended for use with Basler 5GigE cameras:

Marvell AQtion AQC107

For best performance, Basler recommends using the Basler GigE Interface Cards.

Info

You can operate a Basler 5GigE camera with a 1GigE network adapter. However, the camera's bandwidth will be limited to 1/5 of its maximum bandwidth.

Network Adapters and Network Drivers#

Although Basler recommends the adapters listed above, the cameras should work with any compatible network adapter card.

Info

If the adapter is not a recommended network adapter, you may experience stability issues, e.g., image data loss. Also, the performance of your system may be degraded.

Using a recommended network adapter also lets you benefit from the pylon GigE Configurator, which automatically optimizes your system for optimum performance and reliability.

The pylon GigE Vision drivers and tools optimize and lower the CPU load caused by network traffic between the computer and the cameras. In addition, they come with very robust packet resend mechanisms to assure maximum stability and reliability of your GigE Vision setup.

Installing the Camera#

This procedure assumes that you want to establish a peer-to-peer connection between your GigE camera and a computer.

ace 2 Connectors#

ace 2 Connectors

ace Connectors#

ace Connectors

To install the camera:

  1. Remove the protective cap from the lens mount.
  2. Mount a C-mount or CS-mount lens onto your camera. Be careful not to insert the lens any deeper than specified in the Maximum Allowed Lens Intrusion topic.
  3. Connect the camera to the computer and power.

    • If you are using Power over Ethernet (PoE) with a PoE-capable computer (recommended option)
      1. Plug one end of the Ethernet cable into the Ethernet connector of the camera and plug the other end of the cable into the PoE-capable GigE network adapter port of your computer.
    • If you are using Power over Ethernet (PoE) with a PoE injector
      1. Plug one end of an Ethernet cable into the "In (or similar) port of the power injector and plug the other end of the cable into the GigE network adapter port of your computer.
      2. Plug one end of an Ethernet cable into the "Out" (or similar) port of the PoE injector and plug the other end of the cable into the Ethernet connector of the camera.
      3. Use the power cord that shipped with your power injector to connect the injector to an AC outlet.
    • If you are using a power supply
      1. Plug one end of an Ethernet cable into the network adapter port in your computer and plug the other end of the cable into the Ethernet connector of the camera.
      2. Plug the 6-pin connector of the cable from your power supply into the 6-pin connector of the camera.
      3. Switch on the power supply.

    The camera starts up and will go through several initialization steps including IP address assignment. This takes some time.

Info

If your system is configured to show network connection icons in the Windows system tray, you may see a yellow exclamation point on the icon. You may also see a message about limited connectivity. You can ignore the icon and the message as they don't affect the camera.

Next Steps#

  • Use the pylon Viewer to check whether your camera has been detected, acquire images, display images, and adjust parameter settings to improve image quality.
  • In most cases, you must configure your network before you can use the camera.